Information for users
EN ISO 21420:2020, Protective EN instructions glove 388:2016+A1:2018, against carefully mechanical EN risks In and cold accordance risks. with the PPE of the CATEGORY Regulation II EN
511:2006
EN also Levels number, (classes) Purpose: agriculture, 388 Design: of Material: the the are performance I They cold etc.). higher A(0-4) determined may Cotton ther BZARO serve Designed are environments. knit based protection as based for a on WINTER” fully upon the factor). Abrasion (freezing protection ther tests covered manipulating results off by carried resistance: plants, of hands PVC, out cold in materials in laboratory with against Code: storage accordance foam both tests, dirt dry and industry, which with insulation and do the r protection not damp fishing, 3700 insert conditions in 012 necessarily and the collection 250 environments. warm reflect determined a 00 working of flannel actual U Putt areas garbage, the the where lining. valid conditions gloves workers cleaning Size: on standards in the dry. work, have specified clean workplace. to water 11 face1 hands. below. The supply (U) (The mechanical protection and higher 2016/425. sanitation, levels the hazards
Read the
requirements
Product:
Performance level
Blade cut resistance (coupe test)
The protection works only against the
B(0-S)
Performance level
specified hazards. Do not use the gloves
Tear resistance
c04)
Performance leve
as a protection against different hazards
Puncture resistance
and classes. The results apply only for the
D(04)
Performance level
Cut Resistance (TDM)
model classes, not for the protection
EA-R
Performance level X
Impact protection
A.B.C.D.E.F. levels (classes). As for the gloves with
F (P/Xor nothing)
Performance level
T
two or more layers it does not necessarily
Resistance to convective cold
a(0-4)
EN 511
Performance level
reflect the properties of the outer layer.
b(0-4)
Resistance to contact cold
to
The protection levels (classes) apply only
Performance level
c (Oor1)
Water penetration
for new gloves not washed or cleaned.
Performance level
X
protective gloves (general requirements
The hand sizing system 15 based on hand
EN ISO 21420
Dexterity
ab.c
circumference and hand length as defined
0)
Performance level
in EN ISO 21420 Annex B, table B1.
“”= test noi performed or not applicable.
Please note: The user must check the gloves before and after use to verify that they are in the required condition. Do not use as a protection against other
hazards and classes. Do not use for manipulating sharp objects, toxic chemicals greasy objects. Gloves material may be damaged by oil, mineral oil,
Or
greasy and solvent organic. This glove doesn’t give a protection fora temperature under-30C. This glove provides a protection for a limited contact time with cold
Gloves when soaked lose their insulating properties. It is not allowed to wear these gloves in cases with risk of entanglement with moving parts
can
items.
of machines. Due to the dulling of the blade during the cut resistance test (B) the results of the cut tests are only indicative, while the TDM (E) cut resistance
test 1s the result of the reference design. The gloves comply with the requirements for puncture resistance. However, they are not meant for protection
of
against thin, sharp objects, such as injection needles. The mentioned facts may help the user for rational use of this type of protective gloves. It is the
oft
responsibility of every user to judge, whether the gloves are used in suitable conditions.
Maintenance, lifetime: After use, make sure the gloves are removed from all pollutants. Thus, you will extend their lifespan. The gloves are designed for
e
single or short-term use only Dry a damp muff gloves away from sources of heat at the room temperature. Gloves should not be washed. Any dirt should
be brushed out using a soft brush, or wipe with a damp cloth. Do not clean chemically, bleach, dry in a tumble dryer, or iron. Wor through, burned through,
strongly fouled or stiffened pairs have to be replaced with new ones. We are not responsible for any reduction of the protective function due to incorrect
care. Under suitable storage conditions, shelf life is 2 years.
Storing and transport: Storing 1n a clean, dry and ventilated place at the room temperature, without any contamination by moisture, dirt, mould, or other
agents reducing the level of protection. Do not expose it to solar radiation. The supplier doesn’t provide warranty for such damage. Store and transport the
best in original sealed packaging. Accessories: The product is supplied without accessories.
Dangerous admixtures: The product does not contain any substances, which are known for their adverse impact on hygiene and health of users
On
nor there are suspected of it. In spite of that, the materials which come into contact with a user’s skin can cause an allergic reaction in sensitive
a
individuals. If skin irritation or allergic reaction do not use gloves and contact your doctor immediately
Disposal: Dispose of used gloves with respect of the soiling level according to the applicable disposal regulations and the regulations of the local authority.
Unused gloves can be disposed of with domestic waste.
The Notified Body that performs conformity assessment: Notified Body No. 0075, CTC-Centre Technique Cuir Chaussure Maroquinerie, 4 rue Hermann
Frenkel, 69367 Lyon Cedex 07, France
The Declaration of Conformity can be found here: www .canis.cz; for individual products, in the bar “Documents to download”.
to
fori
Marking (sample)-description:
Symbol indicating the necessity to to read the
Type of gloves
ZARO WINTER
instructions
Identification production
Manufacturer identification
11
Size
“A’
EN388
EN511
Pictogram and number of the standard that the
product complies with
S
Results of the tests carried out
XXIXXXX
XXIXXXX
ZAAXXNXXX
CATI
Month and year of production
Use by date (month / year)
Lot- mark/year of production forder number
Glove Category
3121X X1X
CE
Conformity mark
If you need more information, please contact:
Poděbradská 260/59, Hloubětin, 198 00 Praha 9, Czech Republic